Choosing a 1.5m or 2m shower hose is mainly a reach and routing decision, but length is not the only check. Measure the installed route, inspect both threaded connections, confirm the end shapes and check the shower manufacturer’s requirements before ordering.
Counter rule: do not buy the longest hose by default. It needs enough slack for normal movement without pulling tight, dragging heavily on the tray or forming a loop that catches underfoot.
Quick shop: 1.5m or 2m shower hose options
Scudo Smooth Shower Hose — 1.5 Metre
Scudo identifies HOSE001 as a 1.5m smooth hose in chrome-finished rubber and plastic with a 1/2 BSP hose connection. It suits a measured installation where 1.5m reaches the handset position without being stretched.
View the 1.5m Scudo hose
Euroshowers Silver Strong Shower Hose — 2 Metre
The exact 82728 model is listed as a 2m PVC hose with 1/2-inch female ends. The extra half metre is useful only when the valve-to-holder route or required handset movement genuinely needs it.
View the 2m Euroshowers hoseFor other measured options, browse APM’s shower hoses collection.
1.5m or 2m shower hose: start with the installed route
Measure from the shower outlet to the handset connection while the handset is sitting in its normal holder. Then check the movement needed by the person using it. The hose should reach without loading either threaded joint. It also needs a relaxed curve when the handset is returned to the holder.
Do not measure a straight line through the air if the hose must pass around a bath rim, a valve body or a rail. Follow the real route with a flexible tape or a piece of cord, mark the required length and then measure the cord. Compare that figure with the old hose laid out without stretching it.
A 1.5m hose is the cleaner choice when it provides full useful reach and hangs without tension. A 2m hose gives another 500mm for a higher rail, a bath-shower mixer, cleaning the enclosure or other legitimate movement. The longer option is not automatically better in a compact tray because surplus hose can drag, twist or sit where it is stepped on.
| Site condition | What to check | Likely direction |
|---|---|---|
| Compact enclosure with outlet close to the rail | Can 1.5m reach every normal handset position with a relaxed curve? | Use 1.5m if the measured route passes comfortably |
| Bath-shower mixer or wider enclosure | Does the handset need to reach beyond the usual showering position? | Consider 2m after checking where the spare loop will hang |
| Existing hose pulls against the outlet | Is it genuinely short, incorrectly routed or trapped around the rail? | Correct the route first; move to 2m only if length remains the limit |
| Existing hose forms a large floor-level loop | Is excess length causing snagging or abrasion? | A measured 1.5m replacement may give a tidier drop |
Check the threads and end shapes before choosing length
Both featured products are documented with 1/2-inch shower-hose connections, but that does not justify assuming every old installation is identical. Remove the old hose only when the shower is off and cool, retain its washers, and compare each end with the proposed replacement. Check the mixer or outlet end, the handset end and any swivel or conical section that locates in a holder.
The Scudo 1.5m smooth shower hose is the manufacturer-identified HOSE001 model. The Euroshowers 2m Silver Strong hose is model 82728. Those exact identifiers matter: a similar silver hose or a similar length does not prove the same material, end detail or connection.
Use the sealing washer intended for the hose connection. Do not rely on thread seal tape to compensate for a damaged washer, split nut or mismatched fitting unless the exact manufacturer instructions call for it. Hand-start both nuts squarely so the threads do not cross. Tighten only by the product instructions, then run the shower and inspect both joints under normal operating flow.
1.5m or 2m shower hose: allow movement without strain
Test the full working movement before calling the length correct. Lift the handset from the holder, move it through the positions actually required, and return it without pulling the valve connection sideways. On an adjustable rail, check both the usual and highest legitimate holder positions. On a bath mixer, check the practical cleaning or rinsing reach rather than stretching the hose to its absolute limit.
Then look at the hose at rest. A gentle hanging curve is preferable to a tight bend immediately below the outlet. Keep it clear of sharp edges and hot surfaces. If a 2m hose creates a heavy loop that rubs the bath, catches a control or lies in the tray, revisit the route or choose the shorter measured option.
Bore, material and finish come after fit
Length and connections decide whether the replacement physically fits. Construction and finish then help select between products that pass those first checks. Scudo’s HOSE001 documentation describes rubber and plastic construction with a chrome finish. The exact Euroshowers 82728 listing describes PVC construction. Neither material label removes the need to protect the hose from kinks, abrasion and over-tightened connections.
Do not infer flow performance from outside diameter or appearance. Where bore size, maximum pressure, temperature or system compatibility matters, use the exact hose and shower manufacturer data. A hose that fits the thread can still be unsuitable if its operating limits or end arrangement do not match the shower.
Replacement check before leaving the job
- Confirm the shower is off and the hose has cooled before removal.
- Record the old hose length, routing and end shapes before discarding it.
- Measure the real outlet-to-handset route and the movement genuinely required.
- Compare both threaded ends and sealing faces with the exact replacement.
- Fit sound washers and start every thread by hand without forcing it.
- Route the hose with a relaxed curve and no sharp bend at either nut.
- Run the shower through its normal range and check both connections for leaks.
- Move the handset through its working reach and confirm the hose neither pulls tight nor creates a trip or snag point.
Bring the old hose or measurements to APM in Acton
Bring the old hose if practical, or take clear photographs of both ends beside a ruler. Record the length along the hose rather than guessing from the bathroom size. APM can then compare the Scudo 1.5m smooth hose, the Euroshowers 2m Silver Strong hose and other shower hose options against the installation details.
Specification sources: Scudo’s HOSE001 product data sheet confirms the 1.5m model details. The exact Euroshowers 82728 length and construction are corroborated by the Silver Strong 200cm product listing. Always recheck the current product page and the shower manufacturer’s instructions for the installation in front of you.
24 Western Avenue, Acton, W3 7TZ
020 8702 8080
Check the exact product page before travelling, then bring the old hose or measured connection details to the trade counter.
Leave a comment